Topeak's FlashStand is a super work/display stand that folds up to become extremely portable as well! This affordable two-footed wonder supports your bike at the bottom bracket and down tube and raises the rear wheel with two adjustable-height feet. Take it along in the trunk of your car to dial-in your ride before your next adventure!
A pro level workstand with a built-in digital weight scale. Stable tripod design folds down small for travel or use at the races. Additional clamp lever for tightening / releasing the clamp with ease. Clamp Head Non-marring rubber jaws 360° rotation Digital weight scale Clamp Height 122 cm to 183 cm (48” - 72”) Clamp Opening 1.9 cm to 4.5 cm (0.75” - 1.8”)
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
115 pound (52kg) base plate with floor levelers for the PRS-33 Power Lift Shop Stand
Park's Deluxe Home Mechanic Repair Stand is an awesome portable stand that's as useful while traveling as it is at home. This versatile stand features Park's shop-quality Micro-Adjust Clamp that handles round and aero seatposts and frames from 7/8-inch to 3-inches in diameter and clamps securely with its quick-release cam and handle that fine-tunes the tension. The clamp also has protective rubber jaws and built-in slots for cables. Plus its jaws are only 2.7 inches tall so they easily fit in narrow areas, like on seatposts that aren't raised much. The Deluxe Stand also boasts a stable base and the top telescopes for putting the bicycle right where you need it to get your work done efficiently. Plus, you can also rotate bicycles 360 degrees and the stand folds for easy carrying and storage.
Park Tool's Deluxe Home Mechanic Repair Stand is a heavy-duty folding stand with your choice of shop quality clamps. Perfect for heavier duty home use or portable shop use, the PCS-4 features a rock-solid, four-point leg system that folds together for storage, steel powder-coated tubing, and a composite horizontal tube. • PCS-4-1 uses the 100-5C Adjustable Linkage Clamp. • Clamp rotates 360º and is adjustable in height up to 67” (170cm) • Adjusts quickly from 55" to 72" • Approximate weight 26 lbs (11.8 kg) NOTE: The maximum weight holding capacity of the PCS-4 is 45 kg (100 lb.). However, this assumes the weight is centered over the legs.
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).
The standard of the bike industry for over 40 years, the PRS-2.3 clamps two bikes and rotates horizontally 360 degrees, allowing one bike to be swung out of the way to work on another. Stand height and clamp position are firmly secured in place using our proven lock block system. Built from heavy-gauge oversized steel tubing, then chrome plated and powder coated for years of carefree use. The PRS-2.3-1 features our 100-3C Adjustable Linkage Clamps, with a time-tested design and straightforward operation. - Maximum weight capacity: 120 lbs. (54 kg) - Clamp capacity: 0.875" to 1.625" (22–41 mm) diameter tubes - Clamp jaws are nominally 4" (100 mm) wide - Clamp height: adjustable from 50" to 62" (128–158 cm) - Includes #105 Cast Aluminum Work Tray & RPP-1 Repair Stand Post Protector - Can be installed onto the #135 Repair Stand Base or bolted directly to the floor using the FP-2 Floor Plate (both sold separately)
- The PRS-2.3.1 is a professional quality double arm repair stand designed and built to withstand the rigors of everyday shop use. - Includes two 100-3D Micro Adjust Clamps (clamps tubes up to 3", fully adjustable clamping pressure, narrow 2.7" clamping jaws) - Clamps two bikes simultaneously - Clamps rotate 360 degrees horizontally and vertically - Heavy gauge, chrome plated steel tubing for rigidity and years of trouble free use - Clamping height easily adjusts from 50" to 62" (128cm to 158cm) using heavy duty lock block and locking pin system - Includes aluminum work tray - #135 Steel Base Plate sold separately - Use FP-2 Floor Mounting Plate to mount stand directly to floor (sold separately)
The PRS-26 incorporates proven features from our other Team Issue stands to produce a strong, lightweight repair stand that's at home on-the-go or in the race pits. The sturdy tripod leg design folds and unfolds quickly and easily, and provides stability on any surface. The clamp is height-adjustable from 97 to 147 cm (38" to 58"), and can be positioned over one leg or between two legs to accommodate any bike. Precisely constructed from anodized 6063 T6 lightweight aluminum and durable composites, the PRS-26 is our lightest full-featured repair stand, and folds compactly for storage or transport. The PRS-26 is equipped with the time-tested 100-25D Micro-Adjust Clamp, the same design featured on our shop repair stands. The 100-25D features narrow clamping jaws to fit into tight areas or on short seat posts, and clamps nearly any tube from 23 to 76 mm (7/8" to 3"), including aero tubes and dropper posts. The cam-actuated adjustment system allows for quick entry, adjustment and exit. - Maximum weight capacity*: 36 kg (80 lbs.) - Clamp capacity: round and aero tubes from 22 to 76 mm (7/8" to 3") wide - Jaw width: 70 mm (2.75") - Height adjustable from 97 to 147 cm (38" to 58") - Base when open forms a triangle of 126 x 126 x 126 cm (49.6" x 49.6" x 49.6") - Weight: 5.7 kg (12.6 lbs.) - The PRS-26 uses the 100-25D Micro-Adjust Clamp - Replaceable jaw covers (part #1960) *NOTE: The maximum weight capacity of the PRS-26 assumes the bike's center of gravity is positioned directly below the clamp.
- 150lb holding capacity - Includes work tray (#105) (900119-01) - Base not included (900706)
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Walk into the service area of any bike shop in the world, and odds are good you'll see a Park Tool Professional Wheel Truing Stand on the bench still the top choice of professional mechanics everywhere for over 40 years, and for good reason. With extra-tall uprights and wide calipers, the TS-2.3 is capable of accepting most wheels commonly found on road, mountain, BMX, and hybrid bicycles, including wheels with disc brakes, aero rims, and oversized MTB tires. Upright adjustment is controlled with an ergonomically-designed speed knob, which quickly adjusts the stand to accommodate any hub width in seconds. The sturdy uprights of the TS-2.3 feature integrated storage for the included thru-axle adapters, which allow for compatibility with thru-axle, quick release, and solid axle hubs without the use of additional parts or adapters. The TS-2.3 is constructed from durable powder-coated heavy-gauge steel and is manufactured, assembled, and calibrated in St. Paul, Minnesota. Strong, comfortable knobs and spring-loaded calipers and caliper arm ensure smooth, consistent operation, and the removable composite caliper tips protect painted rims and fragile materials. 100% adjustable and rebuildable for a lifetime of use. Wheel Capacity: - Maximum wheel size: Up to 29" + with or without tire - Maximum hub width: 200 mm (7.87") - Maximum rim width: 102 mm (4") - Hub compatibility: Accommodates quick release and solid axle hubs, also accommodates thru axle hubs using included TS-2TA.2 Thru Axle Adaptors Mounting Options: - Bolt to benchtop — mounting holes are 9.5 mm (3/8") in diameter and 200 mm (7.9") from center to center - Clamp in vise — base is 76 mm (3") deep - Install in TSB-2.2 Truing Stand Base
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
$9.14 - $20.99
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
Have you ever wondered why all Feedback Sports bike repair stands have exposed frame above the clamp head? Our Pro Truing Stand is designed to sit atop all of our portable stands! The truing stand also includes a free-standing steel base and a bench-mount adapter for when you're not traveling to races and top-secret trailheads. This single-arm, precision wheel and rotor truing stand is awesome at home and excels at races, events, or adventure-riding weekends. And with the all-new Thru-Axle Adapter, it can accommodate the most common wheel sizes for quick-release or thru-axle hub designs. Use the benchtop mount for an awesome tubeless setup and tubular gluing station. - All-New Thru-Axle Adapter accommodates: 10mm, 12mm, 15mm and 20mm – up to 157mm wide hubs (SuperBoost) - Single-arm design is lightweight, portable and compatible with most wheel systems - Precision spring-loaded tip can verify lateral and radial rollout - Measurement arm includes a disc brake rotor truing slot - Steel base measures 10.25 x 8.5-inches (26.5 x 21.5cm) and 5.8lbs (2.6kg) - Bench mount measures 4 x 6-inches (10.1 x 15.2cm) - Anodized 6061 T6 aluminum construction is ultralight, corrosion resistant and incredibly durable - Can accommodate up to 29-inch wheel with tire mounted - 9mm quick-release hubs use quick-release for mounting - 12mm, 15mm and 20mm thru-axle adapter included - 3-Year Warranty
The Pro Elite Bike Repair Stand is the premier portable and home service partner for the most demanding bike mechanics. Its lightweight, compact, and durable design delivers unmatched stability, adjustability and portability. The patented ratchet-action closure and speed release clamp is capable of managing any bike frame, up to 85lbs (39kg) and tube diameter up to 2.6? (6.6cm). Be the most popular rider at the trailhead or in your neighborhood with the Pro-Elite Bike Repair Stand. Add a Wheel Truing Station, Bottle Opener and Team Edition Tool Kit for the ultimate service setup.
Being a "shade tree mechanic" doesn't mean you should lean your bike against a tree. You paid hard-earned money for your family's bike collection and we've got a budget-conscious, yet feature-loaded bike repair stand that's perfect for the home bike mechanic. The price-point leading 360-degree rotating clamp can position your bike optimally for any work you're planning. Plus, the Recreational Stand leverages a 52-inch (132cm) wide base with rubber-coated end caps for fantastic stability on any surface. And when the service day is done, it folds into a space-saving unit for storage. Add a Tool Tray, Bottle Opener and a Pro Truing Stand for the complete at-home bike shop. - Seatpost clamp features Spinner Knob for quick closure and precision clamping pressure - 360-degree rotating clamp design provides easy access to any part of your bicycle - Fixed clamp height at 55-inch (139cm) - Rubber-coated clamp secures and protects expensive components and beautifully painted frames - Clamp opening up to 1.9-inch (4.8cm) accommodates even the largest diameter frame tubes - Powder-coated steel construction is corrosion resistant and incredibly durable - Stiff 52-inch (132cm) base and rubber-coated end caps create ultimate stability even on uneven surfaces - Total load capacity of 60lbs (27.2kg) accommodates service on most road, mountain bikes, fitness bikes, and electric bikes - Portable and compact construction creates a remarkably small folded footprint of 10 x 4 x 55-inches (25.4 x 10.2 x 139.7cm) - Optional Travel Bag available - At 13.8lbs (6.3kg), moving in and out of storage is no problem - No assembly required - 3-year Warranty
The Sport Mechanic Bike Repair Stand prioritizes the most critical aspects of the entire Feedback Sports bike repair stand lineup – compatibility, stability, durability and portability. The 360-degree rotating clamp uses a spinner knob closure that can accommodate up to 1.9? (4.8cm) and support 65lbs (29.5kg). Plus, the Sport Mechanic leverages the same 54? (137cm) wide base, with rubber-coated end caps, for amazing stability on any surface. And when the service day is done, it folds in to a compact unit for storage or travel. Add an available Travel Bag and a Tool Tray for the optimal bike maintenance setup.
Page 1 of 2 Next page